10 tons pressure gasket machine for ptfe plastic polymer gaskets by SuKo...

Explanation of main test indicators of PTFE products

PTFE products are a special type of plastic, which is quite different from other plastics. According to the industry standard of the Ministry of Light Industry, the PTFE products produced must meet the requirements of the index. Below we list the definitions of the 13 main test indicators for PTFE products for reference.

1. The coefficient of linear expansion indicates the degree of expansion or contraction of the material. It refers to the expansion ratio of the finished polytetrafluoroethylene plastic at a temperature of 1 ° C under a certain pressure, expressed as the coefficient of linear expansion relative to the unit length. This coefficient is one of the important indicators for understanding the degree of change in product size with increasing temperature of PTFE products, expressed in units of 1/°C or 1/K. The coefficient of linear expansion coefficient is α = ΔL / (L * ΔT), where ΔL is the change in the length of the object at the given temperature change ΔT, and L is the initial length. The linear expansion coefficient of PTFE is about 10-12*10-5/°C (ambient temperature 25-250°C), ie (0.01-0.012)%, and the linear expansion coefficient of PTFE is 10~20 times that of iron, which is larger than most plastics. 

2. Thermal conductivity: Also called thermal conductivity, it reflects the thermal conductivity of the material. It is defined as two parallel planes with an area of ​​1 m2 perpendicular to the direction of heat conduction inside the object. If the temperatures of the two planes differ by 1 K, the heat is transferred from one plane to the other in 1 second. The unit is defined as the thermal conductivity of the substance, and its unit is watt·m-1·open-1 (W·m-1·K-1). It is a reference indicator for studying the thermal insulation of target products when designing products.

3. The tensile strain at break is the tensile strain corresponding to the tensile fracture stress when the sample of the polytetrafluoroethylene product is not fractured under the tensile load, and the tensile strain is just when the sample material is plastically shaped. The ratio of the difference between the length to the original length and the original length, expressed as a percentage (%).

4. Tensile strength: In the test of tensile specimens, the critical value of the transition from uniform plastic deformation to local concentrated plastic deformation, characterizing the resistance of the material to the maximum uniform plastic deformation, is also the maximum load carrying capacity of plastic under static tensile conditions ( Maximum tensile stress). The unit is MPa. 

5. Elongation at break: It is the increment of the index from the original unit length (ie the rate of change of length), which is the ratio of the difference between the length of the pull-off and the original length to the original length, expressed as a percentage (%).

6. Electrical strength: A parameter indicating the breakdown of equipment insulation at a certain rated voltage, indicating the degree of insulation of the product withstand voltage. It means that under certain conditions, the ratio of the breakdown voltage to the thickness of the sample to be broken is the electrical strength of the product.

7. Breakdown voltage: The voltage at which the test piece breaks down is the highest voltage before being penetrated. That is, the sample does not break down at this voltage. The breakdown is usually caused by a partial discharge in the gas or liquid medium surrounding the sample and the electrode, and the sample at the edge of the smaller electrode (or equal-diameter two electrodes) is destroyed.

8. Density The ratio of the mass of a substance to its volume, that is, the mass of a substance per unit volume, is called the density of this substance. Kilograms/meter 3 or 1 gram per cubic centimeter 1.0 x 103 kg/m3 of polytetrafluoroethylene plastic products are usually tested by dipping, liquid pycnometer and titration.

9. Withstand voltage is the sample between the electrodes, the power frequency AC voltage rises to the voltage before the breakdown is the withstand voltage of the sample.

10. Fracture Nominal strain refers to the tensile strain corresponding to the fracture stress when the tensile specimen is not yielded and the fracture specimen is subjected to the specified specimen size, and the % is expressed by a dimensionless ratio or percentage.

11. The longitudinal dimensional change rate means that the pipe (100 ± 1) with a certain length is placed in a (260 ± 2 ° C) oven for 3 hours, and taken out at a normal temperature of 23 ± 2 ° C for 4 hours. The length of the treated sample is The percentage of the difference between the original size and the original size.

12. Dielectric strength is a measure of the electrical strength of a material as an insulator. It is defined as the maximum voltage per unit thickness that a unit is subjected to when it is broken down, in volts per unit thickness. The ratio of breakdown voltage to sample thickness. The breakdown voltage is tested according to GB/T1408.1-2006. The dielectric strength is in kilovolts per millimeter (KV/mm).

Introduction to seal gasket

With the advent of mechanization era, a variety of machinery and equipment emerge in endlessly, in a variety of mechanical equipment, sealing gaskets become unnecessary parts, is the industrial production enterprises and related industries to solve the gas, liquid medium "run, run, drip, leakage", root cure leakage effective tools.

As the name suggests, the seal gasket is a seal, mainly play the role of sealing, it is generally used for machinery, equipment, pipelines and other places where there is a fluid through.Used for connection between pipes or parts of equipment.

Popular at present, the market of sealing gaskets are metal or nonmetal after cutting, stamping or tailor made after processing, such as the common have high pressure asbestos rubber gasket, oil resistant rubber gasket, cylinder gasket, aramid fiber gasket, asbestos gasket, asbestos gasket, rubber mat and so on seven big classes, different material sealing gasket its specific applicable environment is different also, if the gasket failure, not only affects the operation of equipment, sometimes even cause an accident, a threat to the personal and property of people.

Relevant data shows that different gaskets have their national standards are different, in quality, density, corrosion resistance, lubricity resistance, oxidation resistance and other aspects of strict requirements, as long as all the parameters to achieve national standards, before entering the market.

Sealing gasket is commonly used in ptfe gasket, with good flexibility, compression resilience, creep resistance, high and low temperature resistance and excellent corrosion resistance, aging resistance, self-lubrication.With its very low leakage rate and excellent heat resistance and radiation resistance, and at the same time very convenient installation and use, is the chemical industry, medicine, petrochemical, food and beverage, electronics, power, metallurgy, shipping and other industries extremely ideal sealing material.

PTFE Plastic Gasket Making Machine

PTFE Plastic Gasket Making Machine

Gaskets Making Machine Features:Efficiently producing: 300pieces/h(large size);More energy saving: the total power only 5KW;More friendly to environment: no PTFE powder splashing but powder output automatically;More precise: producing gaskets by controlling the power quantity;More time saving : the power cut off automatically while the production number set up;Longer working life : no heat while working. More:Plastic Machine.

Data:

Name	Description
model	automatic ptfe gaskets molding machine
main motor	3.5KW
range of speed	750r/s-1500r/s
powder motor	0.25KW
speed	1400r/min
total power	5KW
the stroke of bent axle	40mm
max diameter	300mm
capacity	100mm-300mm
max depth	2mm-10mm
processing speed	300pieces /h-400pieces/h
the max pressure	25T
net weight	3000kg
package size	1800x1800x2500mm
package way	plywood case
payment term	L/C,T/T,Western Union,Paypal
delivery time	15-30 days upon confirmation

Packing size :
1)main body : 1800x1800x2500mm
2)plywood case : 1800x1800x2500mm

Source:http://www.sukoptfe.com/gasket-making-machine